
How to Compare Hot Water System Running Costs in Australia
Last Updated: November 21, 2026
Quick Summary
To compare how to compare hot water system running costs, multiply your daily hot water energy use by your own tariff and by 365, then adjust for each system's efficiency. Use the rule of thumb of about 0.047 kWh per litre heated by roughly 40°C, and run low, typical and high usage scenarios. Check your bills for the rates that actually apply to you.
- Gather your last four quarterly bills and note your tariff rate in cents per kWh or per MJ.
- Estimate daily litres used: about 50 litres per person is the typical use scenario in the article.
- Heating one litre by roughly 40°C takes about 0.047 kWh of delivered heat energy.
- Divide delivered heat by the system's efficiency to get the input energy you actually pay for.
- Add purchase, installation and maintenance over 10 years to compare lifecycle costs, not just running costs.
Table of Contents
- What You Need Before You Start Comparing
- Estimate Your Hot Water Usage by Household Size
- Calculate Running Costs for Gas and Electric Systems
- Use the Energy Rating and a Cost Calculator to Check Your Numbers
- Frequently Asked Questions
What You Need Before You Start Comparing
Knowing how to compare hot water system running costs in Casino comes down to three things: your current energy bills, your household's daily hot water use, and the energy rating label on each system. Check whether your current system is failing and needs replacing before you start comparing.
Gather your last four quarterly electricity or gas bills. Note your tariff type and supply rate in cents per kilowatt-hour, or cents per megajoule for gas. Write down the number of people in the home, since this drives most hot water use.
Estimate Your Hot Water Usage by Household Size
Start with a daily hot water volume in litres at the tap.

Then convert litres to energy. Heating one litre of water by roughly 40°C takes about 0.047 kWh of delivered heat energy, giving a simple planning formula:
Daily delivered heat energy (kWh) ≈ litres used × 0.047
So a two-person household at 50 litres per person uses about 100 litres a day, or roughly 4.7 kWh of delivered heat. A four-person household at the same rate uses about 200 litres, or roughly 9.4 kWh. A high-use household of four might reach 300 litres, or about 14 kWh.
Those figures are delivered heat, not the energy drawn from the grid or gas line. Divide by the system's efficiency to get the input energy you actually pay for. Conventional electric storage is close to 1.0. Gas storage or continuous flow divides by the star-rated efficiency, a 5-star unit is typically around 0.85-0.90, an older 2-star unit closer to 0.60. Heat pumps divide by the coefficient of performance (COP), which varies by model and season. Solar thermal is different again because the sun supplies part of the load, so booster energy depends on tank size, collector area and backup use.
Use three scenarios rather than one: low use (about 30 litres per person per day), typical use (about 50) and high use (about 75). Run every system through all three. This sensitivity analysis is where rankings can change: a heat pump that wins at typical use may lose some advantage at very low use once purchase price is included, while a gas unit can look competitive at low use but fall behind at high use.
Watch out: do not use bedrooms as a proxy for occupancy. A three-bedroom home with one occupant uses far less hot water than a two-bedroom home with four, and sizing demand to the house rather than the people will skew the comparison.
Calculate Running Costs for Gas and Electric Systems
Annual running cost = daily input energy (kWh or MJ) × tariff rate × 365
For electricity, the tariff rate is your cents per kilowatt-hour including GST. Electricity tariffs vary by retailer and plan, so check your own bill for the rate that applies to your hot water circuit. A controlled-load (off-peak) circuit dedicated to the hot water cylinder is usually cheaper per kWh but only heats during set windows, suiting storage rather than instantaneous units. Check your own bill for the rate that applies to your hot water circuit, using the general supply rate for a controlled-load system overstates the running cost, and vice versa.
For gas, the tariff is usually cents per megajoule, and you must add the daily supply charge, which applies whether you use gas or not. A continuous-flow unit has no storage losses; a gas storage tank does. Convert carefully: 1 kWh equals 3.6 MJ, so 3.5 cents per MJ is roughly 12.6 cents per kWh of gas energy before efficiency is applied.
Here is a worked example using the typical four-person household from the previous section, about 9.4 kWh of delivered heat per day, and a flat electricity rate of 30 cents per kWh:
Those figures are illustrative only, your tariff, climate and actual usage will move them. The point is the method: convert delivered heat to input energy using the system's efficiency, then multiply by your own tariff and by 365.
Running cost is only half the comparison. A like-for-like lifecycle comparison adds purchase price, installation, maintenance, expected service life and any rebates over a consistent period, say 10 years, then divides by the number of years for an average annual cost. A heat pump typically costs more upfront than a gas continuous-flow unit but far less to run, so the crossover depends on how long you stay and how much hot water you use. Compare heat pump, gas and electric options for Northern Rivers homes to see how they stack up locally.
Watch out: heat pump efficiency is rated at standard test conditions, and real-world COP in the Northern Rivers falls in cooler months and rises in warmer ones. Use the manufacturer's rated figure but treat the annual result as a range, and check whether the defrost cycle or backup element will run during cold snaps.
The article sets out the core running cost calculation, with the key variables for each fuel type summarised below.
| Input | Value stated | Note |
|---|---|---|
| Heat to raise 1 litre by ~40°C | 0.047 kWh | Delivered heat energy |
| Annual running cost formula | Daily input energy × tariff × 365 | Use your own tariff |
| Electricity tariff unit | Cents per kWh (incl. GST) | Check your bill |
| Gas tariff unit | Cents per MJ | Add daily supply charge |
| Energy conversion | 1 kWh = 3.6 MJ | Needed for gas comparisons |
| Example rate used | 30 cents per kWh | Illustrative only |
| Lifecycle comparison period | 10 years | Average annual cost |
Use the Energy Rating and a Cost Calculator to Check Your Numbers
The energy rating label on a new system shows its expected energy use. Use that alongside a cost calculator, such as the Rheem Running Cost Estimator or the Compare Water Heating Costs tool, to test how changes in usage or tariff affect the result.
If you want help reading a label or checking your numbers before you buy, book a hot water system quote with Northern Rivers Hot Water and our team will walk you through the figures for your home.
Frequently Asked Questions
How do I calculate the running cost of a hot water system?
Start with the system's daily energy use, which is shown on its energy rating label or in the manufacturer's data. Multiply that daily energy use by 365 to get annual energy use in kilowatt hours (kWh) for electric systems or megajoules (MJ) for gas. Then multiply by your tariff rate in AUD per kWh or per MJ, using the rate on your latest bill. Add any daily supply charges that apply only to that system. The result is an estimate of annual running cost. Check the figure against two or three calculator results to confirm it is reasonable.
Is gas or electric hot water cheaper to run?
It depends on your local gas and electricity tariffs, so there is no single answer that holds across Casino and the wider Northern Rivers. Compare the annual running cost for each option using your own tariffs, not average national prices. Gas storage and instantaneous systems often have lower running costs per litre heated than standard electric storage, while heat pump systems usually cost the least to run. Use the same household usage figure for each option so the comparison stays like for like.
How do household size and hot water use affect running costs?
Running costs rise in direct proportion to how much hot water you use. A household of two typically heats far less water each day than a household of five, so the same system can have very different annual costs. Count the number of showers, loads of washing and dishwasher cycles each day, then estimate litres of hot water used. Run your comparison at both a low and a high usage level to see how sensitive the result is to your household's habits.
Need help with your hot water system?
Call Northern Rivers Hot Water for a free, no-obligation quote. We service Lismore, Ballina, Byron Bay, Casino and all surrounding areas.
0472 580 441